Code
0710
Description
Washable finish for internal rooms based on acrylic resins in water emulsion and special luminescent particle - size pigments, which gives the product a special reflection of sand.
Use
This product can be applied to wall surfaces, properly prepared with concrete, where a luminescent aesthetic appearance combined with excellent resistance to washing with cleansing agents are required.
Appearance of the film
Luminescent
Color
Color chart
Component
1
Hardening
Physical hardening through evaporation of water and union of the polymer
Specific weight
From 1,41 gr/lt
VOC
40 gr/ liter
Minimum thickness
50 -60 micron
Estimated yield
9 m² / kg for a thickness of 50 microns
Flash point
Component A > 114°C
Temperature Resistance
Max 60°C
Preparation of surfaces
New surfaces:
Apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Old surfaces: remove any parts that are peeling off and, after a careful cleaning of the substrate, apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Old surfaces: remove any parts that are peeling off and, after a careful cleaning of the substrate, apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Preparation of the product
Product ready to use. Mix the product before the use
Component A 100
Component A 100
Environmental conditions
Ambient temperature: from + 5 to 40° C
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Drying and hardening time
For the thickness of 50 microns 10° C 20° C 30° C
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 - 5 2 hours
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 - 5 2 hours
Time of overpainting
Minimum (hours) 10° C 20° C 30° C
8 4 3 hours
Maximum unlimited in the absence of contaminants
8 4 3 hours
Maximum unlimited in the absence of contaminants
Application
After an appropriate preparation of the substrate, apply the product as follows:
Apply a coat of our white primer « SABBIAFOND » with a brush or a roller diluted with water to 20 - 25 %. In order to have the colors of our color chart, add the amount shown on the chart « Platinum Line » of our dye Toner.
Apply a coat of « SABLE », undiluted, with the special brush.
You can have two effects depending on the application method:
Puff effect: the product is applied with the special brush, always following the same direction.
Storm effect: the product is applied crossing brush strokes in an irregular way, paying particular attention to not leave areas where the paint is spread precisely. Wait a few minutes and pass again the special brush without color on the surface
Apply a coat of our white primer « SABBIAFOND » with a brush or a roller diluted with water to 20 - 25 %. In order to have the colors of our color chart, add the amount shown on the chart « Platinum Line » of our dye Toner.
Apply a coat of « SABLE », undiluted, with the special brush.
You can have two effects depending on the application method:
Puff effect: the product is applied with the special brush, always following the same direction.
Storm effect: the product is applied crossing brush strokes in an irregular way, paying particular attention to not leave areas where the paint is spread precisely. Wait a few minutes and pass again the special brush without color on the surface
Shelf life
2 years in a cool and dry place (max 40° C
Packs
Comp A Kg. 2 – Kg. 5.