Code
0801
Description
Acrylic resin - based emulsion hydro enamel for indoor and outdoor use with high resistance to chemical and atmospheric agents. Exceptional washability, coverage, expansion and brushability make « Velax » a unique product
Use
It is suitable for the treatment of interior surfaces in schools, hospitals, nursery schools, or for environments where a high resistance to washing and sanitization must be guaranteed.
It can be applied on new or old plasters, concrete and plaster surfaces, plasterboard, old paints or absorbent mineral substrates.
It can be applied on new or old plasters, concrete and plaster surfaces, plasterboard, old paints or absorbent mineral substrates.
Appearance of the film
Glossy
Colour
White and colour chart
Component
1
Hardening
Physical hardening through evaporation of water and union of the polymer
Specific weight
From 1,330 gr/ml
Volume of solids
40 %
VOC
12 gr/ liter
Estimated yield
6 mq /L
Flash point
Component A > 114°C
Temperature Resistance
Max 60°C
washability
> 25000 touches
Preparation of surfaces
New surfaces:
New plasters or patches must be well cured, clean, dry and free from white layer.
In the presence of moulds, treat the surface with a suitable restoring product. Remove any efflorescence by brushing or washing. Prime clean surfaces with our water-based acrylic fixative product « H95 IMPRIMITURA ». For outdoor application we recommend priming the surfaces with « H 95 IMPRIMITURA » or solvent - based product « PRIMER/P ».
Already painted surfaces:
Remove the parts of paint that are peeling off; in the case of tempera or lime based paints, remove them completely by washing and brushing.
Prime the surfaces with our acrylic insulating product « H95 IMPRIMITURA » or « PRIMER/P ».
New plasters or patches must be well cured, clean, dry and free from white layer.
In the presence of moulds, treat the surface with a suitable restoring product. Remove any efflorescence by brushing or washing. Prime clean surfaces with our water-based acrylic fixative product « H95 IMPRIMITURA ». For outdoor application we recommend priming the surfaces with « H 95 IMPRIMITURA » or solvent - based product « PRIMER/P ».
Already painted surfaces:
Remove the parts of paint that are peeling off; in the case of tempera or lime based paints, remove them completely by washing and brushing.
Prime the surfaces with our acrylic insulating product « H95 IMPRIMITURA » or « PRIMER/P ».
Notes
To bring out the features of the satin « Velax », it is necessary to prepare the surfaces perfectly smooth and flat.
Preparation of the product
Mix the product before the use and add water
Component A 100
Water 1° coat 15 - 20 % - 2° coat 10 - 15 %
Component A 100
Water 1° coat 15 - 20 % - 2° coat 10 - 15 %
Environmental conditions
Ambient temperature: from+ 8 to 40°C
Temperature of the surface : > 10°C
Humidity: 0 – 80 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Temperature of the surface : > 10°C
Humidity: 0 – 80 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Warnings
Do not apply on wet or not well cured substrates
Do not apply at temperature below 10° C;
Do not apply when moisture is above 80 %, in case of imminent rain and in the presence of wind
Do not apply at temperature below 10° C;
Do not apply when moisture is above 80 %, in case of imminent rain and in the presence of wind
Drying and hardening time
For the thickness of 100 microns 10° C 20° C 30° C
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 2 hours
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 2 hours
Time of overpainting
Minimum (hours) 10° C 20° C 30° C
8 4 2 hours
Maximum unlimited in the absence of contaminants
8 4 2 hours
Maximum unlimited in the absence of contaminants
Application
Brush, roller, spray
If you use the brush, you have to use nylon or pure bristle brushes.
If you use the roller, you have to use medium - haired rollers.
Use the cross - hand method for application
If you use the brush, you have to use nylon or pure bristle brushes.
If you use the roller, you have to use medium - haired rollers.
Use the cross - hand method for application
shelf life
2 years in a cool and dry place (max 40° C)
Packs
Comp A Lt. 14 Lt. 5 Lt. 2,5